Ask a question

Barium in well water: limit, sources and treatment

5 min readBy Updated Sources checked3 sources
Hand holding a clear glass of drinking water
Photo: Unsplash
Short answerBarium in well water is a natural mineral element, and EPA's drinking water limit is 2 mg/L. EPA lists an increase in blood pressure as the potential health effect of long-term exposure above the limit. It has no taste or smell, so test it. Water softeners and reverse osmosis can both reduce barium.

Key facts

What barium is

Barium is a metal that occurs naturally in many rocks and soils. It dissolves into groundwater at levels that vary by region. EPA's regulatory table lists the sources of barium in drinking water as the discharge of drilling wastes, discharge from metal refineries, and erosion of natural deposits.

Barium is not the same as barium sulfate, the harmless compound used in medical imaging, which does not dissolve. Barium in water is the dissolved form.

The federal number

Barium reference
ItemValue
EPA MCL2 mg/L
Potential effect above the MCL (EPA)Increase in blood pressure

The limit applies to public systems, and private wells are not covered. Use 2 mg/L as your benchmark. If you take blood pressure medication or have a heart condition, bring a high result to your doctor.

Where barium shows up

  • Wells in areas with barium-bearing rock
  • Wells near oil and gas drilling or waste disposal
  • Wells near metal refineries or old industrial sites
  • Wells with high hardness, because barium behaves like calcium

Because barium acts like calcium and magnesium in water chemistry, it often appears in hard water.

How to test

Ask for barium on a metals panel at a certified lab. If drilling or industrial activity is near the well, also ask about chloride and total dissolved solids, which can signal brine or drilling fluid. Use the sample bottle that comes from the lab and fill it as instructed.

Treatment options

Barium removal
MethodNotes
Water softener (cation exchange)Removes barium along with hardness; the resin and its waste hold the barium
Reverse osmosisReduces barium at one tap
DistillationRemoves barium; small volumes
Boiling, carbon or sediment filterDo not remove barium

A softener is often the practical choice when water is also hard. Because it takes barium out, the brine waste carries it, so check local rules about disposal. Softener resin needs regular regeneration to keep removing barium, so keep the salt stocked, and retest the softened water after a few months.

SafetyIf your result is above 2 mg/L, use bottled water for drinking and cooking until treatment is working, and ask your health department about drinking water for anyone with high blood pressure.

What to do right now

  1. TestOrder barium and a standard hardness test.
  2. Compare with 2 mg/LIf above, switch the drinking tap.
  3. Check for nearby drillingIf so, test chloride and TDS.
  4. Treat and recheckUse a softener or RO and test the treated water.

Common mistakes

  • Assuming a hardness-only test shows barium
  • Letting salt run out in the softener
  • Ignoring nearby drilling or disposal sites
  • Using a carbon filter and assuming it works

If your area has oil and gas activity, keep a record of dates, test results and any change in odor, color or taste. A pattern can help your state agency follow up.

How common it is

Many private wells have a little barium, and in most cases it is well below the limit. Where barium becomes a problem, it is usually tied to local rock or to nearby industrial or drilling activity. A state geological survey or health department can tell you whether barium has turned up in wells near you.

If your area has oil or gas wells, ask the state agency that oversees them whether they offer baseline water testing. A before-and-after record can be useful.

Reading a barium result

How to read the number
ResultWhat it meansNext step
Below 2 mg/LUnder EPA's limitRetest every few years or after nearby drilling
Near 2 mg/LClose to the limitRetest soon and watch the trend
Above 2 mg/LOver EPA's limitSwitch the drinking tap and plan treatment

Check the units on the report. Some labs report barium in µg/L, and 2 mg/L equals 2,000 µg/L.

Softener care when barium is the target

If you use a softener to remove barium, the resin has to be regenerated with salt on schedule. A softener that runs out of salt stops removing barium and can release some of what it held, so keep the brine tank stocked and retest the softened water at the first few intervals. Ask the installer how to size the unit for your hardness and your barium.

Softeners that are set to run by volume of water used protect better than ones set only by the clock, because they adapt to how much water you use.

Barium and drilling activity

Barium is used in some drilling fluids. If oil or gas work happens near you, a baseline test before work starts and a test after is the best evidence of any change. Keep the reports, with dates and the lab name. If barium jumps and chloride jumps with it, report that to the state agency that oversees drilling.

Barium also lets you see the value of a complete mineral panel. Hardness, chloride and TDS together tell whether the well is pulling brine or ordinary hard water.

What to do with the waste from a barium softener

Brine from a softener that is removing barium carries the barium to the drain. Many places allow this to go to a septic system or sewer in ordinary amounts, but rules differ, so ask your health or environmental agency. If you have a septic system, ask the installer how the brine affects it.

Keep the salt tank clean and use a salt grade that the softener maker recommends, since dirty salt can cause resin problems.

Questions people ask

What is the limit for barium in drinking water?

EPA's limit for public systems is 2 mg/L.

What are the health effects of barium in water?

EPA lists an increase in blood pressure for long-term exposure above the limit.

Does a water softener remove barium?

Yes, cation exchange softeners can remove barium along with hardness.

Where does barium in well water come from?

Natural rock and soil, and in some places drilling wastes or metal refineries.

Sources

This page explains general practice for US private wells. Check your state's rules on the state pages, use a certified lab for testing, and hire a licensed well contractor for electrical or well work. See our editorial policy.

Still not sure what to do?

Ask us about your situation. A real person reads every question.

This field is required.
We reply by email. We never share it without your permission.Enter an email address like name@example.com.
Describe what you are seeing and anything you have tried. Plain words are fine.Please write at least 20 characters so we can help.
Choose your state so we can point you to the right rules.
Prefer the full form?

Thanks, we have your question.

We read every message and reply by email, usually within a few working days. If it is urgent (sickness, a positive E. coli test, or a flooded well), use bottled water and call your county or state health department now.

Find your state's well program

Keep reading

Related guides

All 35 contaminants guides