Ask a question

Who to call for a well pump: contractor or plumber

4 min readBy Updated Sources checked3 sources
Plumber repairing pipework in a bathroom
Photo: Unsplash
Short answerCall a licensed well contractor when the problem may be in the well, pump, pipe or wire down the hole. Call a plumber for leaks and fixtures inside the house, and an electrician for panel or house wiring faults. If you are unsure, start with the well contractor, who can test the system.

Key facts

Three trades, three areas

A private well system spans a lot of ground. It starts in the earth with the well, the pump and the wire. It continues through the buried water line and the pressure tank, then the plumbing in the house. Electrical power runs through the whole thing. Different trades cover different parts of that chain.

Who handles what
ProblemBest first call
No water, pump will not runLicensed well contractor
Pump runs but little or no waterLicensed well contractor
Pressure tank, switch or cyclingWell contractor or a plumber experienced with wells
Leak inside the house or at a fixturePlumber
Leak in the buried line from well to houseWell contractor, plumber or excavation company with experience
Breaker will not stay on, panel problemLicensed electrician
Water quality (taste, odor, bacteria)State-certified lab, then a water treatment pro

These lines overlap. Many well contractors also do tanks and switches. Some plumbers service wells. Ask about their experience with private wells before you book.

Why a well contractor is the usual first call

  • They have the tools to test amps, voltage and insulation resistance.
  • They have the equipment to pull and set a pump safely.
  • They know local well code and what is allowed.
  • They can tell whether the problem is in the pump, the pipe, the wire or the well itself.
  • They know how to disinfect a well after repairs.

A plumber who does not work on wells may not be able to tell a pump fault from a pressure switch problem. They may suggest replacing parts they can reach and miss the real cause.

How to check a contractor

Rules differ by state. Many states license or register well drillers and pump installers. Your state health or environment agency or the state licensing board can tell you what applies. Ask for a license number and proof of insurance, then check them with the issuing office.

  • Ask how long they have worked on pump systems.
  • Ask for a written, itemized quote.
  • Ask what warranty covers parts and labor.
  • Ask if they will flush and disinfect the well after opening it.
  • Ask for references from nearby homeowners.
TipCheck your state or county health department website for a list of licensed well contractors. The National Ground Water Association and WellOwner.org also help owners learn what questions to ask.
SafetyElectrical safety: a well pump runs on household power that can seriously injure or kill. Turn off the pump breaker before touching any wiring, control box or pressure switch, and confirm the power is off with a proper tester. If you are not sure what you are doing, hire a licensed well contractor or electrician.

What to have ready when you call

  1. Describe the symptomsSay what happened, when it started and whether anything changed first, such as a storm, a power outage or recent work.
  2. Report what you checkedTell them whether the breaker is on, whether the pump hums, and what the pressure gauge reads.
  3. Know the systemPump age, type, well depth and tank size help if you have them.
  4. Ask about timing and chargesAsk when they can come and whether they charge a trip fee.
  5. Keep water use lowSave water if the tank still has pressure.

Emergencies

If you have no water, a pump that smells burnt, a hot control box or water spraying near electrical parts, shut off the pump breaker and call right away. Do not keep resetting a tripping breaker. If water has flooded the well or pump area, treat the water as unsafe until it is tested.

If a contractor turns up and recommends big work without explaining the cause, it is fine to pause and ask questions. A second opinion is cheap compared with a pump you did not need.

Red flags when hiring

  • A demand for full payment before any work starts
  • No license number, no insurance or no written quote
  • A diagnosis with no measurements behind it
  • Pressure to replace everything without showing the old parts
  • Advice to bypass a breaker, overload or relief valve
  • A refusal to explain what was done or to leave you the old parts

A good contractor is happy to explain what they found and why they are recommending a fix. If they cannot, get a second opinion.

After the repair

Ask for an invoice that lists the parts, the work done and the warranty. Keep it with your well log. If the well was opened, plan a bacteria test with a state-certified lab after flushing and disinfection. Testing at least once a year for coliform bacteria and nitrate, and after repairs, is the standard advice.

Take photos of the new parts and the wiring if the contractor allows it, and note the date. This record helps if a warranty claim is needed, and it helps the next technician.

What not to do while you wait

Do not open the pressure tank or remove covers from the control box. Do not reset the breaker repeatedly. Do not pour chemicals into the well. Use stored water for drinking and cooking if the pump is down, and keep water use low so the tank lasts. If anyone has a medical need for running water, tell the contractor when you call.

If you are unsure about your water after a failure, boil or buy water for drinking until a certified lab confirms the water is safe. Boiling does not remove every contaminant, so for chemical concerns follow your health department's advice.

Questions people ask

Should I call a plumber or a well contractor for a well pump?

Call a licensed well contractor for pump, pipe and wire problems in the well. Call a plumber for leaks inside the house. If unsure, start with the well contractor.

Do plumbers fix well pumps?

Some do, especially tanks and switches, but many do not work on submersible pumps. Ask about their experience with private wells.

How do I find a well pump service near me?

Check your state licensing board or health department, ask neighbors on wells, and look for contractors with local references. Verify the license and insurance.

Do I need an electrician?

Only if the problem is in the panel or house wiring. A well contractor can handle pump circuit tests and many repairs.

Sources

This page explains general practice for US private wells. Check your state's rules on the state pages, use a certified lab for testing, and hire a licensed well contractor for electrical or well work. See our editorial policy.

Still not sure what to do?

Ask us about your situation. A real person reads every question.

This field is required.
We reply by email. We never share it without your permission.Enter an email address like name@example.com.
Describe what you are seeing and anything you have tried. Plain words are fine.Please write at least 20 characters so we can help.
Choose your state so we can point you to the right rules.
Prefer the full form?

Thanks, we have your question.

We read every message and reply by email, usually within a few working days. If it is urgent (sickness, a positive E. coli test, or a flooded well), use bottled water and call your county or state health department now.

Find your state's well program