Ask a question

Constant pressure well pumps (VFD) explained

4 min readBy Updated Sources checked1 sources
Green manual water pump outdoors on a sunny day
Photo: Unsplash
Short answerA constant pressure well pump system uses a variable frequency drive (VFD) to change the pump's speed so water pressure stays steady while you use water. It replaces the usual on and off cycling between a pressure switch's cut-in and cut-out settings, and it often uses a much smaller tank.

Key facts

  • A standard pump system cycles between cut-in and cut-out pressure, commonly 30/50 psi or 40/60 psi, set by a pressure switch.NGWA: WellOwner.org
  • A conventional pressure tank air pre-charge is usually set about 2 psi below the cut-in pressure, with the tank empty of water.NGWA: WellOwner.org

How a standard system behaves

In a standard system, the pump is either on at full speed or off. Pressure rises from the cut-in number, say 40 psi, up to the cut-out number, say 60 psi, then falls as you use water. You may notice the pressure change in a shower when the pump starts. A pressure tank smooths this out and stores water.

What a constant pressure system does

A constant pressure system adds a variable frequency drive, which is an electronic controller that changes the frequency of the power sent to the motor. A faster frequency spins the motor faster. A pressure sensor watches the line, and the drive speeds the pump up or slows it down to hold the pressure at a set target. When you use little water, the pump slows. When you use more, it speeds up. When no water is used, it stops.

Some systems pair a surface drive with a compatible submersible motor, and others use a pump and controller sold as a matched package. The details vary by brand, so follow the maker's requirements for pump and wire.

Standard versus constant pressure

Side-by-side
FeatureStandard (switch and tank)Constant pressure (VFD)
Pressure at the tapRises and falls between cut-in and cut-outHeld near a set point
Pump speedFull speed or offVariable
Tank sizeTank sized for the pumpOften a small tank is enough
Starting surgeFull motor start each timeSoft start, lower surge
ComplexitySimple, familiar to most prosMore electronics, needs trained service
Repair partsCommonMay be brand specific
Upfront costUsually lowerUsually higher, so get quotes

Possible benefits

  • Steady pressure in showers and irrigation.
  • Soft starts that reduce the electrical surge on the motor and a generator.
  • A smaller tank can fit a tight space.
  • Can match flow to demand, which may save energy in some cases.

The energy benefit varies. Some homes see little saving, so do not count on it as the reason to buy. Pressure comfort and smaller tanks are the more common reasons.

Possible drawbacks

  • More electronics means more parts that can fail, such as surges damaging a drive.
  • Repairs may need a pro who knows the brand.
  • Not all pumps and motors work with all drives.
  • A drive may need cooling and a clean, dry place.
  • If the controller fails, some systems stop completely, so ask about a bypass or backup plan, and make sure it does not bypass safety devices.
SafetyElectrical safety: well pumps run on 120 or 240 volts, and a pressure switch, control box or pump wire can shock or kill. Turn off power at the breaker, confirm it is off with a meter, and hire a licensed electrician or pump contractor if you are not trained for the job. Never bypass a breaker, fuse or overload protection.

Questions to ask a pump contractor

  1. Is my existing pump compatible, or do I need a new pump and motor?
  2. What target pressure will you set, and can I change it?
  3. What size tank do you recommend, and why?
  4. What protection does the system include for dry running and surges?
  5. Who services it locally, and what is the warranty on the drive and the pump?
  6. How will the system work with a generator?
  7. What happens during a drive failure?

Do you need one?

Many homes do well with a standard system that has a healthy tank and switch. A VFD makes the most sense if you hate pressure swings, have a long or high demand system or a generator that struggles with startup surges. Ask for a clear comparison on your well rather than a general sales pitch.

What happens during a power outage

A VFD system still needs power to run, so an outage stops the pump just as it does in a standard system. When power returns, the drive restarts the pump, usually with a soft start. Surges are a bigger concern for electronics than for a simple switch, so ask about surge protection at the drive and at the panel.

If you plan to use a generator, a VFD can help because the soft start lowers the startup surge. Ask the maker whether the drive works with your generator's output, since some drives are sensitive to generator power quality.

Setting and adjusting pressure

Most systems let you set the target pressure at the controller. Setting it higher than your plumbing and fixtures are rated for can cause leaks and damage, and setting it very low gives weak showers. Choose a setting that suits your fixtures and write it down. Do not change it casually, and never remove or bypass built-in protections such as the dry-run shutoff.

What to keep in your records

  • The make, model and serial number of the drive and pump.
  • Installed pressure setting and any alarm codes.
  • Wire size and breaker rating.
  • Installer contact and warranty terms.
  • The date of installation and of any service.

These details help the next pro and keep you from guessing when a code shows on the drive display.

Ask for the manual and settings in writing so you can show them to the next pro who services the system.

Questions people ask

What is a constant pressure well pump?

It is a system that uses a variable frequency drive to change the pump speed and keep pressure steady while you use water, instead of cycling between two pressure settings.

Does a constant pressure system need a pressure tank?

It often uses a small tank, mainly to absorb small changes and help the system stop smoothly. Follow the maker's tank recommendation.

Is a VFD well pump worth it?

It depends. Steady pressure, soft starts and a smaller tank are real benefits. Higher upfront cost and more electronics are the tradeoffs. Compare quotes and service options.

Can I add a VFD to my existing submersible pump?

Sometimes, if the pump and motor are compatible with the drive. A pro should confirm before you buy.

Sources

This page explains general practice for US private wells. Check your state's rules on the state pages, use a certified lab for testing, and hire a licensed well contractor for electrical or well work. See our editorial policy.

Still not sure what to do?

Ask us about your situation. A real person reads every question.

This field is required.
We reply by email. We never share it without your permission.Enter an email address like name@example.com.
Describe what you are seeing and anything you have tried. Plain words are fine.Please write at least 20 characters so we can help.
Choose your state so we can point you to the right rules.
Prefer the full form?

Thanks, we have your question.

We read every message and reply by email, usually within a few working days. If it is urgent (sickness, a positive E. coli test, or a flooded well), use bottled water and call your county or state health department now.

Find your state's well program

Keep reading

Related guides

All 29 well pumps guides