Ask a question

How long does a well pump last?

4 min readBy Updated Sources checked4 sources
Old hand water pump against a weathered brick wall
Photo: Unsplash
Short answerThere is no single lifespan for a well pump. Some run for decades and some fail early, depending on how often they cycle, the water quality, sand, power quality, heat and how well the system was installed. Short cycling is one of the biggest preventable causes of early failure.

Key facts

Why there is no fixed number

You will see lifespan figures online, but they are averages that mix good installs with bad ones, big pumps with small ones, and clean water with sandy water. We have no source we can verify for a single national number, so we do not give one. What we can tell you is what moves your pump toward the longer or shorter end.

A pump that starts and stops a normal number of times, runs in clean water and gets stable power can last a very long time. A pump that is oversized, short cycles, sees sand or runs dry may fail in a fraction of that time.

What shortens pump life

Common life-shorteners
FactorWhat it does to the pump
Short cyclingEvery start is a hard load on the motor and switch contacts, so many starts mean fast wear
Waterlogged or undersized pressure tankCauses the short cycling above
Sand and sedimentWears impellers and clogs jet nozzles and screens
Running dry or low waterOverheats the motor because water cools it
Poor power qualityLow voltage or surges raise motor heat and stress windings
Corrosive or mineral-rich waterScale and corrosion attack metal parts and screens
Wrong sizeAn oversized pump pulls the well down; an undersized one runs too long
Heat and floodingA pump control box or switch in a hot, wet or flooded space fails early

What helps a pump last

  1. Keep the tank healthy. Check the air pre-charge once a year with the tank empty of water and the pump off. It should sit about 2 psi below the cut-in pressure.
  2. Do not oversize. Match the pump to your flow and head.
  3. Protect from dry running. A dry-run or low-water protection device shuts power when the well is low.
  4. Fix small problems early. A leaky check valve or toilet that fills in bursts makes the pump start more than needed.
  5. Keep sand out. If the pump pumps sand, call a pro. It may mean a damaged well screen or a pump set too low.
TipWrite the install date and pump model on the panel door or in a notebook near the tank. It helps a contractor, and you will know how old the system really is.

Pump age versus pump health

An older pump that has run smoothly is not necessarily near the end. A young pump that short cycles is not necessarily safe. Look at behavior, not just age. The next section lists what to watch for.

Early warning signs

  • More clicks and starts than before.
  • Weaker flow or pressure that fades during long showers.
  • Air or sputtering from taps.
  • New noises from the pump or at the tank.
  • Higher electric bills with no change in use.
  • Cloudy or sandy water when the pump starts.

Any of these is a reason to look before the pump fails. See our guide to signs your well pump is failing for the checks you can safely do.

Repair or replace?

Costs vary by region, depth and pump type, and we cannot give a reliable range without verified sources, so ask for at least two written quotes. A fair quote lists the pump model, drop pipe and wire changes, tank and switch, labor, and disinfection of the well afterward.

Also ask why the pump failed. If the cause was short cycling or sand and nobody fixes it, the new pump may fail the same way.

Test the water after any pump work

Pulling a pump opens the well. After pump work, ask the contractor about shock chlorination, and send a water sample to a state-certified lab. Test at least once a year for coliform bacteria and nitrate in any case.

How cycling adds up

Every time a pump starts, the motor draws a surge of current and heats up. If your tank is the right size and has the right air charge, the pump starts a manageable number of times per day. If the tank is waterlogged, the pump may start many more times for the same water use. The motor does not know the difference, so the wear adds up.

That is why checking the tank is the cheapest life-extending step you can take. A tire gauge and a few minutes each year can prevent a repair that costs far more.

Questions to ask when buying a replacement

  • Is the pump sized to my flow and head, or just to match the old one?
  • Will you replace the check valve, drop pipe and wire if they are worn?
  • Is the tank the right size for the new pump?
  • Can I add dry-run protection?
  • What does the warranty cover, and does it cover labor?

The answers help you compare quotes on more than price. A lower quote that reuses worn parts may cost more over time.

SafetyElectrical safety: well pumps run on 120 or 240 volts, and a pressure switch, control box or pump wire can shock or kill. Turn off power at the breaker, confirm it is off with a meter, and hire a licensed electrician or pump contractor if you are not trained for the job. Never bypass a breaker, fuse or overload protection.

Questions people ask

How long can a well pump last?

It varies a lot. Pumps that cycle normally, see clean water and stable power can last for a long time. Short cycling, sand, dry running and poor installs can cut life short. We do not quote a single number because it depends on your system.

Can a well pump last 30 years?

It is possible for a pump with good conditions, but there is no guarantee. Watch for warning signs rather than relying on age alone.

Does a submersible pump last longer than a jet pump?

Neither type has a fixed advantage. A submersible sits in cool water and is not exposed to freezing, while a jet pump is easier to service. Conditions and care matter more than type.

What is the most common reason a well pump fails early?

Short cycling is one of the biggest preventable causes. It is often traced to a waterlogged tank, low tank air charge or a leak, and each start puts stress on the motor.

Sources

This page explains general practice for US private wells. Check your state's rules on the state pages, use a certified lab for testing, and hire a licensed well contractor for electrical or well work. See our editorial policy.

Still not sure what to do?

Ask us about your situation. A real person reads every question.

This field is required.
We reply by email. We never share it without your permission.Enter an email address like name@example.com.
Describe what you are seeing and anything you have tried. Plain words are fine.Please write at least 20 characters so we can help.
Choose your state so we can point you to the right rules.
Prefer the full form?

Thanks, we have your question.

We read every message and reply by email, usually within a few working days. If it is urgent (sickness, a positive E. coli test, or a flooded well), use bottled water and call your county or state health department now.

Find your state's well program

Keep reading

Related guides

All 29 well pumps guides