Ask a question

Protecting a well pump from freezing

4 min readBy Updated Sources checked2 sources
Old water pump with a hose attached
Photo: Unsplash
Short answerA well pump can freeze when parts sit in cold air. Submersible pumps are protected underground, but the pressure tank, switch, jet pump and above-ground pipes can freeze. Insulate and enclose the parts, add a safe heat source and keep the wellhead sealed against cold air and water.

Key facts

What can freeze, and what usually does not

Freeze risk by part
PartFreeze riskWhy
Submersible pump in the wellLowIt sits below ground in water
Jet pump above groundHighThe pump casing holds water and can crack
Pressure tankMedium to highWater inside can freeze if the space is cold
Pressure switch and gauge portHighSmall water-filled parts crack easily
Above-ground pipe and fittingsHighWater sits still in them
Wellhead and pitless adapterDepends on depth and installThe pipe leaves the casing below the frost line in a proper install
Water treatment equipmentHighContains water, valves and electronics

Frost depth differs by region, so do not rely on a number from elsewhere. Your pump contractor or local building office can tell you the depth that applies where you live.

Pump house basics

A pump house is a small enclosed shed or box over the wellhead and pump equipment. Its job is to keep the equipment dry, shaded and above freezing. Features that help are insulation, a tight door, a dry floor, ventilation for safety and a way to get to the equipment for service.

  • Keep the wellhead accessible. Do not bury or cover the well cap with soil, boards or storage.
  • Raise the equipment off the floor so splashes and leaks do not reach it.
  • Seal gaps that let in wind but keep an air path if a heat source or fuel is used.
  • Keep electrical parts dry and away from heaters and insulation.
  • Use materials that can be moved or lifted for service.

Heat sources, safely

The two most common choices are electric heat cable and small thermostat-controlled heaters. Each has risks. Heat cable must be rated for the pipe type and installed as the maker says. A space heater in a small enclosure can start a fire if it touches combustible material.

SafetyElectrical safety: well pumps run on 120 or 240 volts, and a pressure switch, control box or pump wire can shock or kill. Turn off power at the breaker, confirm it is off with a meter, and hire a licensed electrician or pump contractor if you are not trained for the job. Never bypass a breaker, fuse or overload protection.
  1. Use equipment made for pump houses or pipe protection, with a built-in thermostat.
  2. Use a properly grounded circuit with a ground fault protection device where code requires.
  3. Follow clearances in the heater manual.
  4. Never use open flames, unvented fuel heaters or extension cords in a pump house.
  5. Check the heat source before each winter and again mid-season.
SafetyDo not run a fuel-burning heater in an enclosed pump house. It can cause fire and carbon monoxide. Use electric devices made for the job, installed by a licensed electrician.

If you cannot heat it

Insulate the tank, the pipes and the pump. Foam pipe sleeves and an insulated box over the tank can add a margin. In a power outage, heat cable and heaters stop too, so on very cold nights know how to drain a jet pump and an exposed pipe, according to your manual.

If the pump has frozen

  1. Turn off powerSwitch off the pump breaker. A pump running with frozen lines can burn out.
  2. Look for splits or leaksCheck for cracked pipe, a swollen tank or a damaged switch.
  3. Warm the space slowlyUse a safe, indirect heat. Do not use an open flame or a high-heat tool on pipes.
  4. Check for damage when thawedLook for leaks before turning the pump on.
  5. Call a proIf anything is cracked or the pump does not run, have it repaired before restarting.

Prepare before winter

  1. Inspect the pump house or enclosure for gaps, rot and drafts.
  2. Check that insulation is dry. Wet insulation does not protect.
  3. Test the heat source and thermostat before cold weather.
  4. Check the pressure tank air pre-charge and fittings. A tank that is waterlogged is heavier and more prone to damage.
  5. Label the pump breaker and the water shut-off so anyone can find them quickly.
  6. Keep a flashlight, a towel and your pump contractor's number near the panel.

Signs of a freeze problem

  • No water, but the pump runs or hums.
  • A gauge that does not move or shows no pressure.
  • Frost or ice on the pump, pipes or tank.
  • Drips or sprays after a thaw.
  • A pressure switch that clicks but nothing happens.

If the water stops on a freezing day, check the exposed pipes and the pressure switch port before assuming the pump has failed. Many freeze-ups are in a short length of pipe near the tank or the wellhead.

Wellhead protection

The well cap and casing must stay sealed and above ground, so snow, melt water and surface runoff cannot enter. In cold weather, soil can heave and crack seals. Check the cap and the ground around it after storms and thaws. If the cap is cracked or loose, or if water pools around the casing, call a licensed well contractor and test the water. A state-certified lab can test for coliform bacteria and nitrate.

After a freeze, check the pressure tank air, the switch and the fittings. A small crack can leak for a long time before you notice. If a pipe has burst or the well cap was damaged, ask about disinfection and testing the water.

Questions people ask

Can a well pump freeze?

Yes. Parts above ground, such as a jet pump, pressure tank, switch and pipes, can freeze. A submersible pump below ground is usually safer, but the pipe and wellhead must still be protected.

How do I keep my well pump from freezing?

Enclose and insulate it, use a thermostat-controlled heat source rated for the job and keep the space dry. Make sure the wellhead and buried pipes are below your local frost depth.

Is a heat lamp safe for a pump house?

A heat lamp can be a fire risk if it touches or is near combustible material. Use equipment made for pump houses and follow the clearances.

What do I do if my well pump freezes?

Turn off power, look for cracks and warm the space gently. Do not turn the pump back on until you have checked for leaks and damage.

Sources

This page explains general practice for US private wells. Check your state's rules on the state pages, use a certified lab for testing, and hire a licensed well contractor for electrical or well work. See our editorial policy.

Still not sure what to do?

Ask us about your situation. A real person reads every question.

This field is required.
We reply by email. We never share it without your permission.Enter an email address like name@example.com.
Describe what you are seeing and anything you have tried. Plain words are fine.Please write at least 20 characters so we can help.
Choose your state so we can point you to the right rules.
Prefer the full form?

Thanks, we have your question.

We read every message and reply by email, usually within a few working days. If it is urgent (sickness, a positive E. coli test, or a flooded well), use bottled water and call your county or state health department now.

Find your state's well program

Keep reading

Related guides

All 29 well pumps guides