Ask a question

Rotten egg smell only in hot water: what the water heater is doing

5 min readBy Updated Sources checked4 sources
Close-up of a white faucet dripping water
Photo: Unsplash
Short answerRotten egg smell only in hot water usually comes from the water heater, not the well. Bacteria in the tank turn sulfate in your water into hydrogen sulfide, often helped by the anode rod. Flushing the tank, raising the temperature briefly, or changing the anode rod type are the usual fixes.

Key facts

Quick diagnosis: three questions first

This page covers the hot-only version. If cold water smells too, read the main rotten egg page instead.

  • Hot only: the heater is the likely source.
  • Hot and cold: the well or the whole plumbing is the source.
  • Hot only after a vacation or power cut: stale water in the tank is a common trigger.

Likely causes, most common first

  • Sulfur-reducing bacteria in the tank (common). Warm, low-oxygen water is a good home for bacteria that make sulfide from sulfate in the water.
  • Anode rod reaction (common). The rod protects the tank steel from rust. A magnesium rod can feed the bacteria that make the smell. Zinc-aluminum alloy and powered rods are alternatives, but check the manufacturer's guidance first.
  • Low tank temperature (common). A heater turned low for savings gives bacteria room to grow.
  • Sulfide already in the well water (less common for hot only). If the cold water smells slightly, heating drives off the gas and makes it more obvious.
  • Sediment in the tank bottom (less common). Built-up sediment shelters bacteria and can add to the smell.

If you see this, check that

Match what you see to a likely cause and a next step
If you seeLikely causeNext step
Smell only from hot tapsTank bacteria or anode rodFlush tank, check rod type
Smell after a long unused periodStale tank waterFlush and reheat; run hot taps for several minutes
Smell fades after a flush, returns weeks laterBacteria regrowthRaise temperature briefly, then fit a different rod
Cold water smells a little tooSulfide in the well waterTreat the source; see the main sulfide page
Rust-colored hot water as wellCorroding tank or rod worn outInspect the rod; call a plumber

Why only the hot water smells

A water heater is a warm, dark tank that holds water for hours. That is a friendly home for sulfate-reducing bacteria, which turn the sulfate found in many well waters into hydrogen sulfide gas. Cold water never sits in a warm tank, so it stays clear of the smell.

The anode rod adds a second factor. It is a metal rod that corrodes on purpose so the tank steel does not. When it corrodes, it releases hydrogen, which the bacteria can use as food. That is why plumbers often suggest a rod made from a different alloy, or a powered rod that does not corrode the same way.

If your water has very little sulfate, the problem is usually smaller. If the smell comes back each time you flush the tank, bacteria are probably regrowing, and you may need to treat the water before it reaches the heater.

Simple checks you can do today

  1. Confirm hot onlyRun only the hot tap at two sinks, then only the cold. Smell each in a clean glass.
  2. Check the temperature settingNote the thermostat setting. Never raise it past the manufacturer's maximum, and keep scald risk in mind with children or older adults.
  3. Flush the tankWith the power or gas off and the manufacturer's directions in hand, drain several gallons from the bottom valve to a floor drain or outside.
  4. Look at the anode rodA plumber can pull the rod. A rod that is mostly eaten away is overdue for replacement anyway.
  5. Retest the smellAfter flushing and reheating, smell the hot water again over the next few days.

What to test for

Treating the heater does not require a lab test, but a bacteria test is smart if the smell is new.

  • Total coliform and E. coli, to rule out contamination of the supply.
  • Sulfate, if you want to know how much material the bacteria have to work with.
  • Iron, because iron can add black or rust staining on top of the smell.
  • Ask for sulfate and iron, since sulfate is the food the tank bacteria use.

A lab will not diagnose a heater, so use your own senses over a week. If the smell vanishes for two to four weeks after a flush and returns, the tank is regrowing bacteria. If the smell never fully leaves, the anode rod is likely driving it. If the smell is faint in cold water too, the well carries sulfide and the heater only makes it obvious. Also note whether the heater sits unused for stretches, such as a vacation home, because stagnant warm water is where bacteria multiply fastest.

Fixes, from cheap to expensive

  1. Flush the tank bottom to remove sediment.
  2. Raise the heater temperature briefly to reduce bacteria, if the manual allows, then return it to a safe setting.
  3. Replace a magnesium anode rod with another type, if the warranty and manufacturer allow it.
  4. Disinfect the tank with a bleach solution following the manufacturer's directions.
  5. Add whole-house sulfide treatment if the cold water smells too.
  6. Replace the tank if it is old and corroding.

Replacing an anode rod is a plumber's job on most tanks because the rod sits under a hex head on top and needs clearance to lift out. Ask whether the new rod type is compatible with the tank warranty, and whether the tank is old enough that replacement is the wiser spend. A powered anode needs an electrical connection, so it should be installed by someone licensed to do it.

When it is a safety issue

SafetyTurn off the power at the breaker, or shut off the gas supply, before draining or opening a water heater. Hot water can scald. Do not bypass or disable a temperature or pressure relief valve. If you smell gas rather than eggs near the heater, leave the house and call your gas utility from outside.

Questions people ask

Why does my water heater smell like rotten eggs?

Bacteria in the tank can turn sulfate in the water into hydrogen sulfide, and some anode rods make that easier. The smell shows only in hot water because the tank is the source.

Is the rotten egg smell from my water heater dangerous?

The sulfide level from a heater is typically a nuisance, not a poison. Still test your supply for bacteria if the smell is new.

Does replacing the anode rod stop the smell?

It often helps when a magnesium rod is the trigger, but results vary, so combine it with a flush and clean tank.

Can I just turn the heater off?

Turning it off does not fix the cause. Flush the tank and fix the conditions that let bacteria grow instead.

Sources

This page explains general practice for US private wells. Check your state's rules on the state pages, use a certified lab for testing, and hire a licensed well contractor for electrical or well work. See our editorial policy.

Still not sure what to do?

Ask us about your situation. A real person reads every question.

This field is required.
We reply by email. We never share it without your permission.Enter an email address like name@example.com.
Describe what you are seeing and anything you have tried. Plain words are fine.Please write at least 20 characters so we can help.
Choose your state so we can point you to the right rules.
Prefer the full form?

Thanks, we have your question.

We read every message and reply by email, usually within a few working days. If it is urgent (sickness, a positive E. coli test, or a flooded well), use bottled water and call your county or state health department now.

Find your state's well program