Ask a question

Testing well water after shock chlorination

4 min readBy Updated Sources checked5 sources
Gloved hand holding a test tube of liquid in a laboratory
Photo: Unsplash
Short answerRetest your well about 1 to 2 weeks after shock chlorination, once the chlorine smell is gone from all taps. Use a state-certified lab and a clean sample. A clear result means the disinfection worked for now. If bacteria return, there is likely a source that needs fixing.

Key facts

What shock chlorination does

Shock chlorination is a way of disinfecting a well and plumbing by adding a strong chlorine solution and letting it sit. It kills bacteria that were introduced during repairs, flooding, or construction, or that caused a positive coliform test.

It is a reset, not a cure. If something keeps letting bacteria into the well, the problem will come back. That is why the retest matters.

Why the retest matters

The retest confirms that the disinfection worked. A clear result is the sign you wanted. A positive result means either the disinfection was incomplete or something is still letting bacteria in.

Many people stop after the chlorine step and assume the job is done. Do not. The only proof is a test from a certified lab.

Timing

Timeline after shock chlorination
StepWhat to do
Day of treatmentAdd chlorine and let it sit as the instructions say
After the contact timeFlush until the chlorine smell is gone at every tap
1 to 2 weeks laterCollect a sample for total coliform and E. coli
After resultsIf clear, resume your yearly schedule; if not, look for a source

The 1 to 2 week window comes from the instructions in the sources used here. Follow the directions you used for disinfection, and ask the lab if they have extra rules.

Before you collect the sample

  • Run water at every tap until you cannot smell chlorine, including outdoor taps and hot water.
  • Check that the water heater and any treatment parts are flushed or have been bypassed as the instructions state.
  • Check that a softener or filter is not holding chlorine.
  • Pick a clean cold tap with no aerator.

Chlorine left in the sample can affect results. Labs often use bottles with a chemical that stops chlorine, but follow their directions.

Steps for the retest

  1. Confirm chlorine is goneCheck by smell, or use a chlorine test strip, at the tap you will sample.
  2. Get the lab's bottleUse the sterile bottle and instructions from a state-certified lab.
  3. Collect carefullyDo not touch the inside of the bottle or cap. See our page on how to take a sample.
  4. Deliver quicklyBacteria samples have short time limits.
  5. Review the reportBoth total coliform and E. coli should be absent.
  6. Record the resultNote the date of disinfection and the date of the test.

If the retest is positive

SafetyKeep using another water source, such as bottled water, until a retest is clear. If E. coli is found, contact your county or state health department.
  1. Check that the instructions were followed, including contact time and flushing.
  2. Repeat the disinfection if the first one was not done correctly.
  3. Look for a source: a loose cap, a cracked casing, a leaking pump seal, or nearby septic.
  4. Ask a licensed well professional to inspect the well.
  5. Retest after any repair.

Repeated positive results after proper disinfection point to an ongoing problem. A professional can look at the well and suggest repairs. Some owners add continuous treatment, such as UV, but it should not replace fixing a source.

Chlorine amounts

Do not guess at the amount of bleach. The amount depends on the water in the casing, which equals 0.0408 times the casing diameter in inches squared, in gallons per foot. A 6-inch casing holds about 1.47 gallons per foot. Use plain, unscented household bleach and never mix chlorine with other chemicals. Our bleach calculator can help you work out amounts.

The lab interpreter tool on this site can help you read the results.

Why timing matters

Testing too soon can give a misleading result. Chlorine may still be in the pipes and can affect the sample, or bacteria from the plumbing may not have settled out yet. Testing too late can miss a problem that you could have fixed earlier. The 1 to 2 week window from the instructions is a balance between these risks.

If you use the water in the meantime, check with your health department or the instructions you used for what is safe. Many people use bottled water for drinking until a clear result is back.

Looking for the source after a repeat positive

  • Is the well cap in place and tight, with a screened vent?
  • Is the casing cracked or too short?
  • Are there septic parts, animal pens, or standing water close by?
  • Is a pit, an old well, or a buried tank nearby?
  • Does the plumbing have a dead end, an old tank, or a water heater at low temperature?

A licensed well professional can check these things and may use a camera to look inside the well. Fix what they find, disinfect again, and retest. Then keep up the yearly test so you catch a return early.

Finally, write down what you did. Record the date and the amount of bleach, the contact time, the date the smell was gone, the date of the sample, and the result. If you ever have to repeat the process, these notes tell you what worked. If you sell the home, they show a buyer that the well was cared for. Store them with the lab reports and the well log, so the whole history is in one place.

Questions people ask

How long after shock chlorination should I test?

About 1 to 2 weeks later, once the chlorine smell is gone from all taps. Follow the instructions you used and any rules from the lab.

Why is my well still positive after chlorinating?

The disinfection may not have been done fully, or something is still letting bacteria in. Check the cap, casing, and nearby septic, and ask a licensed professional to inspect.

Can I test right after flushing the chlorine?

It is usually better to wait, as the sources advise, because a quick test may miss problems. Follow the 1 to 2 week guidance and the lab's rules.

Does shock chlorination fix a bacteria problem for good?

No. It kills bacteria that are present now. If a source keeps letting bacteria in, the problem will return.

Sources

This page explains general practice for US private wells. Check your state's rules on the state pages, use a certified lab for testing, and hire a licensed well contractor for electrical or well work. See our editorial policy.

Still not sure what to do?

Ask us about your situation. A real person reads every question.

This field is required.
We reply by email. We never share it without your permission.Enter an email address like name@example.com.
Describe what you are seeing and anything you have tried. Plain words are fine.Please write at least 20 characters so we can help.
Choose your state so we can point you to the right rules.
Prefer the full form?

Thanks, we have your question.

We read every message and reply by email, usually within a few working days. If it is urgent (sickness, a positive E. coli test, or a flooded well), use bottled water and call your county or state health department now.

Find your state's well program

Keep reading

Related guides

All 29 water testing guides