Ask a question

DIY vs pro installation for water treatment systems

4 min readBy Updated Sources checked3 sources
Kitchen faucet running water into the sink
Photo: Unsplash
Short answerSimple jobs, such as changing cartridges or installing an under-sink unit, are often fine for a handy owner. Work that involves the pressure tank, wiring, chemical feeds, drains or permits is better left to a licensed pro. Always switch off pump power at the breaker, and never bypass safety devices.

Key facts

  • Private wells are not regulated by the EPA, so the owner is responsible for testing and treating the water.EPA: Private Drinking Water Wells
  • Test at least once a year for total coliform bacteria and nitrate, and after flooding, repairs, or changes in taste, smell or color.Minnesota Dept. of Health: Well Water Testing
  • Common pressure switch settings are 30/50 psi and 40/60 psi; the tank pre-charge is usually about 2 psi below the cut-in pressure, with the tank empty of water.NGWA: WellOwner.org

A sensible split

Plenty of treatment work is within reach for an owner who is comfortable with basic plumbing. Some jobs need a licensed professional because mistakes are costly or dangerous. The goal is to know which is which before you start.

Who should do what
JobDIY reasonable?Notes
Change a filter cartridge in an existing housingYesSwitch off pump power and relieve pressure first
Install an under-sink RO unitOftenNeeds a drain connection and careful leak checks
Install a cartridge filter housing on the main linePossible for experienced DIYersAdd shutoff valves and a bypass
Install a UV systemMaybeNeeds power and pre-filters; a pro is wise
Install a softener or backwashing filterPro recommendedNeeds a drain, power and setup of the controller
Install a chemical feed systemProChemical handling and dosing
Work on the pressure tank, switch, pump or wiringProElectrical and pressure hazards
Connect to the well itselfLicensed well contractorRules apply in most states

Safety first

SafetyTurn off power to the well pump at the breaker before any plumbing or electrical work near the pump or pressure tank. If you are not sure how, or if the work involves wiring, hire a licensed pro. Never bypass a pressure relief valve, breaker or other safety device.
  • Relieve pressure by opening a faucet after power is off, before opening any housing or fitting.
  • Do not work on wiring unless you are qualified.
  • Never mix chemicals. Chlorine and acids or ammonia can release dangerous gases.
  • Wear eye protection and gloves when handling chemicals or UV equipment.
  • UV lamps can injure eyes and skin, so never look at a lit lamp.

What a pro adds

A licensed installer brings experience with local codes, permits and inspections. They know how to size equipment for peak flow, add bypasses and sample taps, and set up controllers. They can also test the treated water, show you how to service it, and stand behind the work.

Many areas require permits for plumbing or electrical changes. Ask your county or city building department. Skipping permits can cause trouble when you sell, or with insurance after a leak.

What a DIY job needs

  1. Test and planGet the lab report. Pick equipment and the order of stages.
  2. Read the manual firstCheck required flow, pressure, temperature and power.
  3. Gather partsInclude shutoff valves, unions, fittings, sealant that is rated for drinking water and a bowl wrench if needed.
  4. Shut off power and waterOpen a faucet to relieve pressure.
  5. Install carefullySupport the equipment, use the right fittings and avoid stressing pipes.
  6. Check for leaksTurn power on, repressurize slowly, and check every joint. Check again the next day.
  7. Flush and testRun water until clear. Test the treated water at a certified lab.

Common DIY mistakes

Tools and materials that help

  • Shutoff valves and unions on each side of the unit, so it can be removed later.
  • Thread seal tape or compound that is rated for drinking water.
  • A bowl wrench that fits the housing.
  • Pressure gauges before and after filters.
  • A bucket and towels. Housings hold water.
  • A sample tap after the final stage for test samples.
  • Labels and a marker for valves and bypasses.

Good materials make later service quick. Poor ones turn each filter change into a project.

When to stop and call a pro

If you find corroded pipes, a pressure tank that cycles rapidly, signs of electrical overheating, or a leak that does not stop after tightening, stop. These problems are bigger than the filter you are installing. A licensed plumber, electrician or well contractor can diagnose them.

Also call a pro if your water is unsafe and you are not sure what to do next. For bacteria or nitrate above the limit, your county or state health department can tell you how to keep your household safe while the system is fixed.

Warranty and insurance

Some manufacturers require professional installation to keep a warranty valid, or at least a receipt and photos. Read the warranty before you start. Also think about home insurance. A leak from a poorly installed filter can cause water damage, and an insurer may ask who did the work. A licensed installer's work often comes with some protection if something goes wrong.

If you do install it yourself, take photos at each stage, keep your receipts and write down the date. That record helps with any later claim or sale.

Know where your main shutoff is

Before any work, find the main shutoff valve and the pump breaker, and make sure everyone in the house knows where they are. If a fitting fails, you want to stop the flow in seconds. Keep a bucket, towels and a wet vacuum nearby, and do the work when you have plenty of time and daylight.

  • Skipping shutoffs and bypass valves.
  • Overtightening plastic housings, which can crack.
  • Mixing up inlet and outlet ports.
  • Leaving out a drain air gap where one is required.
  • Installing equipment in an unheated space that can freeze.
  • Not testing afterward.

If you want to try DIY but are unsure, a compromise is to hire a pro for the hard part and do the simpler parts yourself. Some installers will check and sign off on your work for a fee.

Whichever route you take, keep photos of the install, the manuals and the lab reports in one place.

Questions people ask

Can I install a whole house water filter myself?

Many owners do, if they are comfortable with basic plumbing. Add shutoffs and a bypass, turn off the pump power first, and test for leaks. Hire a pro for wiring, drains or the pressure tank.

Do I need a plumber for a water softener?

A softener needs a drain, power and controller setup, so a pro is often wise. Check your local rules.

Is it safe to work near the well pressure tank?

Only with power switched off at the breaker and pressure relieved. If you are unsure, hire a licensed pro.

Do I need a permit to install water treatment?

It depends on your area. Ask your local building or health department.

Sources

This page explains general practice for US private wells. Check your state's rules on the state pages, use a certified lab for testing, and hire a licensed well contractor for electrical or well work. See our editorial policy.

Still not sure what to do?

Ask us about your situation. A real person reads every question.

This field is required.
We reply by email. We never share it without your permission.Enter an email address like name@example.com.
Describe what you are seeing and anything you have tried. Plain words are fine.Please write at least 20 characters so we can help.
Choose your state so we can point you to the right rules.
Prefer the full form?

Thanks, we have your question.

We read every message and reply by email, usually within a few working days. If it is urgent (sickness, a positive E. coli test, or a flooded well), use bottled water and call your county or state health department now.

Find your state's well program

Keep reading

Related guides

All 29 water treatment guides