Ask a question

Lead in well water: where it comes from and what to do

5 min readBy Updated Sources checked4 sources
Hand holding a clear glass of drinking water
Photo: Unsplash
Short answerLead in well water usually comes from your own plumbing, such as old pipes, solder or brass fixtures, not from the aquifer. EPA's health goal for lead is zero, and its action level is 0.015 mg/L (15 ppb). Test the water, flush stale water, and use a lead-certified filter or replace lead parts.

Key facts

Where lead in well water comes from

Well water itself rarely has much lead. Most lead gets in after the water enters your house, from lead pipes in older homes, lead solder on copper pipes, brass faucets and fittings, and some well pump parts. Water that is acidic or low in minerals can dissolve more lead from these parts.

So the key question is not just "what is in my well" but "what happens inside my plumbing." This is why a lead test needs a specific sampling method.

The federal numbers

Lead and copper reference values
ItemValue
Lead action level0.015 mg/L (15 ppb)
Lead health goalZero
Copper action level1.3 mg/L

The EPA page also notes that a revised lead action level of 0.010 mg/L starts on November 1, 2027. These numbers come from the Lead and Copper Rule for public systems. For private wells, EPA does not set rules. The health goal of zero means there is no level of lead known to be completely free of risk.

Health effects

EPA and state health departments say lead can harm the brain and nervous system, and young children and pregnant women are the most vulnerable. Lead can also affect adults. If you think someone has been exposed, ask your doctor about a blood lead test.

How to test

Ask a certified lab for lead, and ask how to take the sample. Labs often want a first-draw sample, taken from a cold tap after water has sat in the pipes for several hours, and some ask for a second sample after a short flush. The pattern shows whether lead is from the fixture or deeper in the pipes.

Ask the lab which sampling method it wants for lead. Most want a first-draw sample from the kitchen cold tap after six hours or more without use, collected in their bottle with no flushing. Do not use the tap for anything beforehand. If the result is high, a second, flushed sample helps tell a fixture problem from a pipe problem.

Also test pH and hardness. Acidic water can eat at metal parts, so a low pH is a clue that the water itself is part of the cause.

What to do right now

  1. Use cold waterUse only cold tap water for drinking, cooking and baby formula. Hot water can pull more lead from pipes.
  2. Flush the lineIf water has sat for hours, run the cold tap until it is noticeably colder before using it.
  3. TestTake a lead test from the tap you drink from.
  4. Use a certified filterChoose a filter certified to NSF/ANSI Standard 53 for lead, and replace cartridges on schedule.
  5. Fix the causeReplace lead parts, and treat acidic water if it is the cause.
SafetyIf you have infants, young children or a pregnant person in the home and your lead result is above the action level, use bottled water or a certified filter for drinking and cooking, and call your health department.

Long-term fixes

  • Replace lead pipes, lead solder joints and old brass fixtures with lead-free parts
  • If water is acidic, treat it with a neutralizer, as covered on the low pH page
  • Install a point-of-use filter or reverse osmosis system certified for lead
  • Ask a licensed plumber to check the pump, pressure tank and fittings for lead parts

Plumbing work can disturb old deposits, so retest after any repair. Boiling does not remove lead.

Common mistakes

  • Testing only a well sample at the pump instead of a house tap
  • Using hot tap water for drinking
  • Using a filter that is not certified for lead
  • Letting filters run past their change date
  • Assuming new plumbing is lead-free without checking the parts

Why pH and hardness matter for lead

Water that is acidic or very soft dissolves metal more easily. Over time, mineral scale can coat the inside of pipes and shield the metal, but acidic water can strip that coating away. If your well water has a low pH, a neutralizer can reduce lead and copper that enter the water in the house.

This is why the best fix is sometimes in the pump room, not at the tap. Treat the water to be less aggressive, and replace the worst parts over time.

How to read a first-draw and flush result

Reading a lead sampling pair
Result patternWhat it suggests
High first-draw, low after flushingLead is in the fixture or short pipe run near the tap
High in both samplesLead may be in the longer plumbing run, or the water source itself; ask a pro
Low in bothLow risk at that tap; test other taps and retest later

Different taps can give different answers, especially in homes with mixed pipe materials. Test the kitchen tap you use most, and any tap used for baby formula.

Know your plumbing

Look at the pipes where they enter the house and near the pressure tank. Pipes that are dull gray and soft, and scratch to shiny silver with a key, may be lead. Ask a licensed plumber to identify any you are unsure about. Homes built before the late 1980s may have lead solder, and some older brass fixtures can leach lead too.

What lead results mean for your household

Reading a lead result
ResultMeaningAction
Not detectedNo lead found at that tap on that dayTest again after plumbing work
Below 15 ppb but above zeroUnder the action level; the health goal is zeroFlush, use cold water, consider a certified filter
At or above 15 ppbAt or over EPA's action levelUse bottled or filtered water; find and replace the source

Because EPA's health goal for lead is zero, many families with young children treat any detectable lead as a reason to use a certified filter or to replace the fixture. Your pediatrician can talk about blood lead testing.

Filters certified for lead need new cartridges on schedule. Write the change date on the unit, since a filter past its life can let lead through.

Questions people ask

Can well water have lead?

The aquifer rarely contributes much. Lead usually comes from household plumbing, solder and brass fixtures, especially if the water is acidic.

How do I test well water for lead?

Use a certified lab and follow its sampling instructions, often a first-draw sample after water has sat for several hours.

How do I fix lead in well water?

Replace lead parts, correct acidic water, and use a filter or reverse osmosis system certified for lead. Use cold water for drinking and cooking.

Does boiling remove lead?

No. Boiling does not remove lead.

Sources

This page explains general practice for US private wells. Check your state's rules on the state pages, use a certified lab for testing, and hire a licensed well contractor for electrical or well work. See our editorial policy.

Still not sure what to do?

Ask us about your situation. A real person reads every question.

This field is required.
We reply by email. We never share it without your permission.Enter an email address like name@example.com.
Describe what you are seeing and anything you have tried. Plain words are fine.Please write at least 20 characters so we can help.
Choose your state so we can point you to the right rules.
Prefer the full form?

Thanks, we have your question.

We read every message and reply by email, usually within a few working days. If it is urgent (sickness, a positive E. coli test, or a flooded well), use bottled water and call your county or state health department now.

Find your state's well program

Keep reading

Related guides

All 35 contaminants guides